INSTALLATION INSTRUCTIONS
GRS Recessed Mount
PDPA/PDPF/PDPH
Upon receipt, thoroughly inspect for any
freight damage which should be brought
to the attention of the delivery carrier.
Compare the catalog description listed on
the packing slip with the label on the car-
ton to ensure you have received the cor-
rect merchandise.
Part No. CJ520709
Page 1 of 2 2/07
Figure 3
Figure 1
Figure 2
IMPORTANT SAFETY INFORMATION
For Your Protection, Read Carefully
WARNING: Risk of fire. Do not install
insulation within 3 inches of fixture sides
or wiring compartment, nor above the
fixture in such a manner as to entrap
heat.
1. Electric current can cause painful
shock or serious injury unless handled
properly. For your safety, always
remember the following:
• Turn off the power supply.
• Ground the fixture to avoid poten-
tial electrical shocks.
• Do not handle an energized fixture
or energize any fixture with wet
hands, when standing on a wet or
damp surface, or in water.
2. Specific safety information concerning
lamps:
• Match wattage of fixture and lamp
exactly.
• Do not remove or insert lamp when
power is on.
• Do not scratch glass or subject lamp
to undue pressure as either may
cause lamp breakage.
• Protect operating lamp from sources
of moisture.
NEW INSTALLATION FOR GRS
Lay-in panel T-bar ceiling:
1. Cut ceiling opening slightly larger
than the outside diameter of the
mounting frame.
2. Position mounting frame through
opening in ceiling. Release clamp-
ing latch arms and adjust channel
bars to the correct spacing be-
tween T-bar as shown in Figure 1.
Secure channel bars to T-bar by
means of wire ties, screws or by
bending ends onto T-bar as shown
in Figure 2.
3. Once mounting frame has been
secured in structure, adjust the
mounting frame vertically to align
the bottom edge to either flush or
slightly above (1/8" max) the ceiling
line. Secure mounting frame into
position by closing the clamping
latch arm.
4. If additional security is required, a
No. 8 sheet metal screw, wire tie or
wire (not supplied) may be used to
tie the latch arm to the mounting
frame as shown in Figure 1.
5. Remove knockouts on junction box to
feed power supply to fixture as
shown in Figure 4. Supply wire must
meet applicable electrical codes
and be rated for a minimum of 75
o
C.
Junction box is thru-wire rated for 8-
No. 12 AWG conductors (4 in-4 out).
6. Complete necessary wire connec-
tions. Snap the door onto the junc-
tion box.
Note 1: For fluorescent applications-
Dimming: Make necessary wire
connections per ballast type.
EL and HID F-Can: Allow for 9-1/2” head
space above for ballast maintenance.
Pivot ballast tray onto spacer brackets
as shown in Figure 5. Thermal protector
assembly must be plugged into the
appropriate power supply voltage (120V,
227V or 347V). Snap door onto the
junction box.
Note 2: For incandescent 277V SDT
applications, make sure a minimum of
9-1/2” head space is available for yoke
height.
7. Pull flex through center hole of
bracket as shown in Figure 3.
8. Center mounting bracket in frame
aperture, and loosen screws until
1/2” from surface (Do Not Remove).
Clamping
Latch Arms
Open
Closed
Bent Tab
T-Bar
Wire Tie
Channel
Bar
MOUNTING BRACKET
CENTER HOLE
FRAME MOUNTING
BRACKET
MOUNTING PAN
Mounting Bracket
Center hole
Frame Mounting
Bracket
Mounting
Pan
SAVE THESE INSTRUCTIONS
(2 pages)
(6 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels